As manufacturers change designs, warehouse stock varies periodically, and the dish supplied may differ from the photographs on this page.

Please feel free to use our Shopping Cart as a calculator without obligation. It will calculate the total order cost for you. Simply add the items you want, select the most appropriate shipping method, then click Recalculate

Question: CAN I PAINT MY DISH? Answer: CLICK HERE

Question: What does a "dish" comprise?

Answer: all our dishes come with an LNB support arm, 40mm LNB clamp bracket and a rear bracket (with elevation adjustment) that will either bolt directly to a wall (wall mount) or to a pole (pole mount) or a bracket suitable for both types of mounting, as specified in the description. Unless otherwise stated, "pole" refers to a 2" diameter steel pole. Brackets to mount additional LNBs are available for some dishes but not for others.

Question: What is a "Pole Mount Dish"?

Answer: A Pole Mount dish normally has a bracket (with elevation adjustment) with two 2" U-bolts that will fit onto anything measuring 2" diameter (50mm). For example, you could fit it to our RAV20 wall tripod or to a ground stand, a combination mount or a pole concreted into the ground or mounted on the wall with T+K brackets. See the Hardware page for suitable mounts.

Question: What pole should I use?

Answer: A 2" diameter steel pole is required for dishes between 60cm and 100cm but note that all ChannelMaster dishes require a 3" mount. Our 43cm Minidishes come with a wall bracket. Some other minidishes (which we don't stock) require a 1.5" diameter steel pole. Always use the shortest possible length of pole. (Never use an aluminium pole for a dish. It's unlikely to be strong enough).

Description

Choose delivery method

NOTE: LNB brackets

LNB brackets are listed for some of the dishes below. One LNB bracket gives approximately 3 to 9 degrees separation. The minimum depends on the width of your LNB. So a 9 degree separation should get you (for example) Astra 1 at 19'E and Astra 2 at 28.2'E. Or Hot bird at 13'E and Astra 1 at 19.2'E. To get Hot Bird and Astra 2 you will need two brackets.

Unfortunately, we can not tell you whether these brackets will fit your own dish.

Zone 1 43cm single minidish by Triax. Spirit level on LNB arm. Includes Quad-output universal LNB, wall bracket and screws. You will require wall-fixing bolts, cable etc.

Zone 1 43cm single minidish by Triax. Spirit level on LNB arm. Includes 8-output OCTO universal LNB, wall bracket and screws. You will require wall-fixing bolts, cable etc.

Zone 1 43cm minidishes four-pack by Triax. Spirit level on LNB arm. Includes Thomson single-output universal LNB, wall bracket and screws. You will require wall-fixing bolts, cable etc.

This dish kit comes bulk-packed FOUR in a box.

Zone 2 minidish for Sky etc.

Raven Zone 2 60cm perforated dish minimises "rain fade" in poorer reception areas and still looks like a "minidish".
Compensates for longer cable runs.

DISKY2 with single-output universal LNB, wall bracket and screws. You will require wall-fixing bolts, 1 rubber boot, silicone grease, cable etc.

Suitable for use with a Sky Digibox or any other digital satellite receiver.
Also suitable for mounting on a 1.5" (38mm) diameter pole. Straight 8' x 1.5" steel pole or cranked pole available if you need to get this dish above a gutter, for example.

More Info HERE and HERE.

Zone 2 minidish for Sky HD and Sky+

The Thomson quad-output LNB normally supplied wih a zone 2 dish has a shower cover that simply slides down. Use plenty of silicone grease in and around the 'F' connectors to keep out moisture.

Raven Zone 2 60cm perforated dish minimises "rain fade" in poorer reception areas and still looks like a "minidish".
Compensates for longer cable runs.

DISKY2QUAD with quad-output LNB, wall bracket and screws. You will require wall-fixing bolts, cable etc. The LNB has a sliding cover to protect the 'F' connectors from direct rain. We recommend using silicone grease to keep condensation out of the connectors. (Rubber boots not required.)

Suitable for use with one or two Sky+ Digiboxes or any other digital satellite receivers. Said to be essential for Sky-HD.
Also suitable for mounting on a 1.5" (38mm) diameter pole. Straight 8' x 1.5" steel pole or cranked pole available if you need to get this dish above a gutter, for example.

More Info HERE and HERE.

The following dishes are for UK mainland delivery only (due to carriage cost).

Choose delivery method

You need a larger dish (made by "Orbital" or similar)

UK mainland delivery only (due to carriage cost).

Solid 80cm dark grey dish for pole-mounting - choose STEEL or ALUMINIUM below.

46377 Extra LNB bracket kit only for 17613 dish £9.95
(Gives 3 - 9 degree LNB spacing. Order 2 brackets if 3 LNBs or extra spacing required).

For LNBs type quantity in the Qty box or leave it as zero. You can add different LNBs from page 1 if you don't want the cheapest listed here.

LNB Brackets are slotted to allow LNBs to be positioned correctly. Click HERE for more info.

You may also wish to order a 2" pole, cable, cable clips, "F" connectors, self amalg. tape, meter, compass, bolts, drill, T + K brackets to suit roof overhang (see below and other pages).

See below for replacement LNB holder.

Choose delivery method

You need an even larger dish (made by "Orbital")

UK mainland delivery only (due to carriage cost).

LNB Brackets are slotted to allow LNBs to be positioned correctly.

You may also wish to order a 2" pole, cable, cable clips, "F" connectors, self amalg. tape, meter, compass, bolts, drill, T + K brackets to suit roof overhang (see below and other pages).

Replacement LNB holder for Orbital 80cm and 1m dishes.

Choose delivery method

TRIAX DISHES

( Indoor satellite dish is on Page 17 )

(Where "pole mount" is specified it requires a 2" diameter steel pole unless otherwise stated)

You may also wish to order a 2" pole, cable, cable clips, "F" connectors, self amalg. tape, meter, compass, bolts, drill, T + K brackets to suit roof overhang.

SEASIDE DISH for where corrosion would be a problem As with all dishes, you can give this a thin coat of paint to match the surroundings if you don't like the design. The screw threads should be given a coating of our silicone grease. The galvanised brackets and metal fittings should be given a good outdoor undercoat, before final assembly, followed by a couple of thick coats of outdoor oil-based paint. We recommend you test the dish at ground level before painting anything as painted items can not be accepted for refund or exchange. To ensure that U-bolt nuts can be undone, a final application of silicone grease can be held in place with self-amalgamating tape, or similar. You can also use "Denzo" tape (try your local plumbers merchant) to weatherproof exposed metalwork. Choose cable and connectors from our other catalogue pages and a 2" steel pole, 2" patio mount (or the TR77S wall bracket from below). The LNB connection should be protected with one of our "rubber boots" filled with silicone grease. UK mainland delivery only (due to carriage cost).

	122901 100 x 105cm Triax TD110 pole mount solid dish £59.95 Qty Include suitable LNB £9.95 Include 4 x LNBs, bracket and DisEqC switch (picture below left) £84.95 Measures 112 x 101cm. UK mainland delivery only (due to carriage cost).
	The bracket and 0.5dB LNBs are designed to allow the LNBs to fit as close together as possible in order to focus on adjacent satellites only 3 degrees apart. Normally this is not possible with ordinary LNBs.

	CH21 90cm Channel Master offset SMC dish face* £79.95 Qty (Includes LNB bracket and legs). Include polar mount £69.95 Include cheap AZ/EL mount £41.95 Include galvanised AZ/EL mount £52.95 Include 3" combi wall/ground mount £69.95 Include suitable LNB £9.95 UK mainland delivery only (due to carriage cost).
	*Note: "SMC" = Sheet Moulded Compound with embedded metal mesh The 90cm and 1.2m dishes can be motorised only if you order the polar mount instead of an AZ/EL mount. You will also need a jack arm (linear motor) and a suitable positioner to control it. See illustration on left. You WILL need to order either an AZ/EL mount or a polar mount (but not both).
	CH22 1.0m Channel Master offset SMC dish face* £89.95 Qty Include polar mount £69.95 Include cheap AZ/EL mount £41.95 Include galvanised AZ/EL mount £52.95 Include 3" combi wall/ground mount £69.95 Include suitable LNB £9.95 UK mainland delivery only (due to carriage cost).
If you have only the 1.0m dish face you will need to order the LNB bracket kit and the kit of 3 "Feed Legs" which support it.	Spare Parts CH45A Feed Legs for channel Master 1.0m dish £29.95 Qty CH48 LNB bracket kit for channel Master 90cm - 1.2m dish £7.95 Qty

Sundries

	01480 2" dia Wall mount adapter for 80cm + 1m dark grey dishes £12.95 Qty See top of page 2a for bolts.
	46377 Extra LNB bracket kit for our 80cm + 1m dark grey dish by Orbital £9.95 Qty LNB brackets are available for some of the dishes on this page. One LNB bracket gives approximately 3 to 9 degrees separation. The minimum depends on the width of your LNB. So a 9 degree separation should get you (for example) Astra 1 at 19'E and Astra 2 at 28.2'E. Or Hot bird at 13'E and Astra 1 at 19.2'E. To get Hot Bird and Astra 2 you will need two brackets. Please note that the plastic moulding that fits on to the Orbital dish arm (<-- red arrow) is not part of this kit as it comes with the Orbital dish itself. Unfortunately, we can not tell you whether these brackets will fit your own dish, even if you tell us the make, model and send a life-size photograph.
	VISION V81-20 LNB bracket This special metal clamp will allow 1 or 2 additional LNBs to be added to the existing LNB to make up a multi LNB dish system. This model is designed for Vision dishes 80cm (C02660), 85cm (A90696) and 1m (A90713). V81-20 Extra LNB bracket kit for Vision dishes £9.95 Qty

---

Choose delivery method

LARGE DISHES

	CH23 1.2m Channel Master offset SMC dish face* £119.95 Qty (Includes LNB bracket and legs). Include polar mount £69.95 Include cheap AZ/EL mount £41.95 Include galvanised AZ/EL mount £52.95 Include 3" combi wall/ground mount £69.95 Include suitable LNB £9.95 UK mainland delivery only (due to carriage cost).
	*Note: "SMC" = Sheet Moulded Compound with embedded metal mesh This dish can be motorised only if you order the polar mount instead of an AZ/EL mount. You will also need a jack arm (linear motor) and a suitable positioner to control it. You WILL need to order either an AZ/EL mount or a polar mount (but not both).
If you have only the 1.2m dish face you will need to order the LNB bracket kit and the kit of 3 "Feed Legs" which support it.	Spare Parts CH45 Feed Legs for channel Master 1.2m dish £29.95 Qty CH48 LNB bracket kit for channel Master dish £7.95 Qty